SANITRX LP™ Rupture Disc
The pharmaceutical, biotech, food and beverage industries rely on the high-precision SANITRX rupture disc family – the perfect combination of industry-leading performance with ASME BPE, USP Class VI and 3A compliance.
The SANITRX LP rupture disc includes all the features of the original SANITRX rupture disc, slightly modified for applications requiring lower pressures with reduced flow resistance.
SANITRX rupture discs can be used in a wide range of sanitary and hygienic applications throughout pharmaceutical, biotech, food and beverage facilities. They fit between industry-standard sanitary ferrules, NA-CONNECT flanges or SANITRX fittings.
To optimize service life and rupture disc performance, we manufacture and test each order of SANITRX rupture discs at your specified compressible or incompressible relief conditions.
Fluoropolymer coating is available for corrosion protection on process or vent sides. Electropolished surface finishes are also available. ASME Code Section VIII, Division 1 compliance available upon request.
ASME BPE Standard
The SANITRX HPX rupture disc family is in compliance with the essential criteria of the ASME BPE standard as follows:
- Clean-in-place and steam-in-place cleanable
- Withstands temperatures of 130°C where steam sterilization is required
- Internal surfaces and sanitary fittings meet SF1 (20 Ra microinch) standard surface-finish requirements
- USP Class VI-certified gaskets are fully traceable, include no animal derivatives and meet other ASME BPE standards
- Discs and fittings are usually made out of 316L SS material; alternates are available if specified by users
- Fully traceable materials
- Fittings are marked and packaged in accordance
The ASME BPE Standard provides requirements applicable to the design of equipment used in the biotech, pharmaceutical and personal care industries, including aspects related to sterility and cleanability, materials of construction, dimensions and tolerances, surface finish, material joining and seals. It applies to components in contact with the product, raw materials or intermediates. Systems that are a critical part of the manufacturing process, such as water for injection (WFI), clean steam, filtration and intermediate storage may also abide by this standard.
Sanitary packaging
The SANITRX HPX rupture disc family is shipped in sanitary, non-toxic, environmentally friendly packaging.
Benefits include:
- Plastic packaging eliminates direct contact of the rupture disc with open cell material, such as cardboard or foam, which can carry contaminants or leave particles on the rupture disc
- Clear packaging provides visibility of the rupture disc tag, allowing verification of the rupture disc specification without removal from the package
- Recyclable plastic package and cardboard carton
- Combined with the vertical tag, the new plastic packaging provides a compact, space-saving container for the rupture disc
- Nominal Size Range: 1″ – 3″ (25 mm – 80 mm)
- Burst Pressure Range: 10 psig – 150 psig (0,69 barg – 10,3 barg)
- Maximum Recommended Operating Ratio: 90% of the rupture disc’s rated (stamped) burst pressure
- Seating Configuration: Industry-standard sanitary ferrules, NovAseptic flanges or SANITRX fittings
- Service: Liquid or Gas
- BDI Alarm System Compatible?: Yes
- ASME Code Symbol Stamp Available?: Yes
Materials not indicated or shown may be available by special design
Food & Beverage Processing
We understand that product purity and safety are critical in food-related industries, so we provide hygienic and aseptic vessels and piping to assure compliance with FDA and 3A requirements.
Relaterade produkter
-
POS-A-SET® Rupture Disc
Relieve ultra-low vacuum or positive pressure conditions with the highly accurate, bidirectional POS-A-SET rupture disc. Our double-acting design allows the POS-A-SET to do the work of two rupture discs with just one installation point. It relieves low positive pressure (as low as 1 inwc) with a girdle and knife-blade assembly on one side, while slightly higher negative pressure is relieved from the other side with perforations and a pre-cut section. Looking for the CAL-VAC rupture disc? Nearly identical to the POS-A-SET rupture disc, the CAL-VAC relieves ultra low-pressure in the negative direction – the inverse of the POS-A-SET’s ultra-low relief in the positive direction. -
WMP Welded Muffled Plug Rupture Disc Assembly
Protect equipment, personnel and the environment with the threaded, single-use WMP Welded Muffled Plug rupture disc assembly. The WMP is ideal for applications that discharge to the atmosphere at the rupture disc. The WMP is a solid-metal, tension-acting rupture disc that screws directly into a threaded port, providing precise overpressure protection with minimal installation time. -
Well Activation and Safety Protection Rupture Discs
Replace shear pins and other moving devices with our Well Activation and Safety Protection rupture discs to save valuable time and labor on the drill site. Designed to release pressure to activate tools in the hole or to protect downhole drill components from overpressure failure, our Well Activation and Safety Protection Rupture Discs use rupture disc technology to achieve high accuracy and reliability. These rupture discs are offered in two burst-direction configurations, Type A and Type I. -
Explosion Vent Panels
Our explosion vent panels provide instantaneous overpressure protection for nearly any type of pressurized dry-bulk handling and storage equipment. The vent panels are designed to allow a full and immediate opening to minimize structural or mechanical damage by expanded gases from the combustion of dust, gases or mists inside equipment, rooms, buildings or other enclosures.
"*" indicates required fields
"*" indicates required fields
Vill du hitta kontaktuppgifter till en specifik person eller kontor?
Här hittar du alla våra kontaktuppgifter.
Med Colly Flowtech får du alltid
